How to make a plant press at home

Build a simple homemade flower press from boards, cardboard and absorbent paper, then layer and press plant specimens flat for keeping.

3 min read1 viewsHow to make a plant press at home
— · 0 votes
Contents
  1. Boards, straps and the press frame
  2. Cardboard and blotting paper layers
  3. Pressing plant specimens flat
  4. Questions About Making a Plant Press
  5. How do you make a plant press at home?
  6. What paper works for pressing plants?
  7. How tight should the straps be?
  8. Can thick flowers be pressed at home?

Making a plant press at home means building a flat sandwich of two rigid boards, absorbent paper and cardboard that squeezes moisture out of plant specimens. A homemade flower press of plywood boards and straps works because the layers pull water away from the plants while the boards hold everything flat. You need only a few materials, and the press can be tightened and reopened as the paper soaks up moisture. The page explains how to build the press, how to layer plant specimens inside it and how to keep the results flat.

Boards, straps and the press frame

Two plywood boards form the rigid frame of a plant press, and straps or bolts hold them tightly together. Cut the boards a little larger than the largest specimen you plan to press, so the edges never crease a leaf. Drill a hole near each corner of both boards and thread a bolt through, or use two webbing straps wrapped around the closed press. Tighten the straps or wing nuts evenly so the boards press down across the whole surface rather than at one corner.

Cardboard and blotting paper layers

Cardboard and blotting paper form the absorbent paper layers that draw moisture out of plant specimens. Place a sheet of cardboard on the bottom board, then a sheet of blotting paper or uncoated absorbent paper on top of it. Each specimen sits on its own paper sheet, with a second sheet laid over the plant before the next cardboard sheet goes down. The cardboard carries moisture away from the paper, and the paper keeps the plant from staining the board.

Pressing plant specimens flat

Pressing plant specimens flat starts with laying each plant between two sheets of absorbent paper while it is still fresh. Arrange leaves, stems and flowers so no part overlaps another, and let roots or thick stems sit toward the edge of the paper. Close the press and tighten the straps, then check the paper after a day and swap in dry sheets when the old ones feel damp. A plant with a thick stem or a fleshy flower needs more frequent paper changes than a thin leaf.

Questions About Making a Plant Press

How do you make a plant press at home?

A plant press at home is made from two rigid boards, layers of cardboard and absorbent paper, and straps or bolts to hold the stack tight. You place a specimen between two paper sheets, sandwich it with cardboard, and close the boards so the press flattens the plant. Tightening the straps compresses the layers, and the paper pulls moisture out of the plant. The finished press stays flat and can be opened to change the paper.

What paper works for pressing plants?

Blotting paper works well for pressing plants because it absorbs moisture quickly without shedding fibers onto the specimen. Uncoated absorbent paper or plain newsprint also draws water away from a plant, while glossy or coated paper blocks moisture. Change the paper when it feels damp so the plant does not stay wet inside the press. Paper that stays dry keeps the specimen from curling or browning.

How tight should the straps be?

The straps on a plant press should be tight enough to flatten the specimen without crushing it into the paper. Even pressure across both boards matters more than force at one corner. Wing nuts or webbing straps let you loosen the press when you swap paper and tighten it again afterward. A press that sits slightly loose still works if the paper layers are dry and changed on schedule.

Can thick flowers be pressed at home?

Thick flowers and fleshy stems can be pressed at home, but they need more attention than thin leaves. Slice a thick stem in half lengthwise or remove some of the fleshy interior so the plant dries evenly. Place the flower face down and spread the petals flat between the paper sheets. Change the absorbent paper sooner for a thick specimen, since it releases more moisture into the press.

Read next

Latest articles